Fracture strength of endocrowns after thermomechanical aging.

This in-vitro study aimed to evaluate the fracture strength (FS; N) of composite, feldspathic, and glass-ceramic computer-aided design/computer-aided manufacturing (CAD/CAM) endocrowns after thermomechanical aging. Seventy non-carious human molars were randomly divided into seven groups, according to the CAD/CAM material used for endocrown fabrication. Intact molars without cavity preparations were used as control (n = 10). Following endodontic treatment, standardized endocrown cavities were prepared and endocrowns were fabricated using composite (Cerasmart270, CS and Grandio Blocs, GB), fired and milled zirconia-reinforced lithium silicate (Celtra Duo, CD), leucite-reinforced feldspar ceramic (LRF Initial, LRF), and feldspathic (Cerec Blocks, CE) materials which were luted with universal adhesive (Futurabond U; Voco) and dual-cure resin cement (Bifix QM). Following thermocycling for 20,000 cycles and 480,000 load cycles in a chewing simulator (CS-4.2, SD Mechatronik), FS was evaluated (Instron). Data were analyzed with one-way ANOVA and post hoc Tukey's tests (p < 0.05). FS was significantly influenced by the tested material (p = 0.00). CS had the highest FS, which was not significantly different from intact molars and fired CD (p > 0.05). There were no significant differences in FS between LRF, GB, and CD, which were significantly higher than CE. Most of the failure modes of CS, CD, and GB were repairable, whereas those of CE were irreparable. All the tested materials withstood clinically relevant axial forces. Composite endocrowns exhibited more favorable fracture pattern, whereas feldspathic and leucite-reinforced feldspar ceramic endocrowns exhibited mostly irreparable fractures.

Depth of cure, mechanical properties and morphology of dual-cure bulk-Fill composites / Profundidad de curado, propiedades mecánicas y morfología de resinas compuestas duales

This study evaluated selected structural and physical properties, such as degree of conversion (DC), Vickers hardness (VHN), and compression strength (CS), of three new dual-cure bulk-fill resin-based composites (RBCs; ACTIVA, HyperFIL, and Fill-Up) and compared them to those of a conventional RBC (Filtek Z250) at three clinically relevant depths. Samples (n=180) were prepared in three depths (2,4, and 6mm). Fourier-transform infrared spectroscopy (FTIR) analysis and VHN and CS tests were performed. The DC value was calculated by considering the relative change in the aliphatic C=C peaks. The fractured surfaces of representative samples were characterized using scanning electron microscopy (SEM). Data were statistically evaluated using two-way analysis of variance and post hoc Bonferroni tests (p<0.05). According to the VHN results, Filtek Z250 showed the highest bottom/top hardness ratio (97.94±1.01) at 2mm thickness and ACTIVA showed the lowest bottom/top hardness ratio (43.48±5.64) at 6mm thickness (p<0.001). According to the FTIR results, the DC decreased with increasing thickness in all materials (p<0.05). Filtek Z250 showed the highest (301±12.4 MPa) and ACTIVA exhibited the lowest (232±17.2 MPa) CS values at 2mm thickness (p<0.05). The lowest CS values were obtained for ACTIVA, and the highest values were obtained for Filtek Z250 for samples with thicknesses of 4 and 6mm, respectively (p<0.05). The structural features of restorative composites, such as the resin chemistry and filler type and content, and the operational parameters (i.e., material thickness and curing conditions) strongly affect crosslinking reactions and thus the DC, VHN, and CS values.

Este estudio evaluó propiedades físicas y estructurales, como el grado de conversión (DC), la dureza Vickers (VHN) y la resistencia a la compresión (CS), de tres nuevos compósitos a base de resina de curado dual tipo bulk (RBC; ACTIVA , HyperFIL y Fill-Up) y los comparó con los de una resina compuesta convencional (Filtek Z250) en tres profundidades clínicamente relevantes. Se prepararon muestras (n=180) en tres profundidades (2,4 y 6mm). Se realizaron análisis de espectroscopia infrarroja por transformada de Fourier (FTIR) y pruebas VHN y CS. El valor de DC se calculó considerando el cambio relativo en los picos alifáticos C=C. Las superficies fracturadas de muestras representativas se caracterizaron mediante microscopía electrónica de barrido (MEB). Los datos se evaluaron estadísticamente mediante análisis de varianza de dos vías y pruebas post hoc de Bonferroni (p<0,05). De acuerdo con los resultados de VHN, Filtek Z250 mostró la relación de dureza inferior/superior más alta (97,94±1,01) con un espesor de 2mm y ACTIVA mostró la relación de dureza inferior/superior más baja (43,48±5,64) con un espesor de 6mm (p<0,001). De acuerdo con los resultados de FTIR, la DC disminuyó al aumentar el espesor en todos los materiales (p<0,05). Filtek Z250 mostró los valores de CS más altos (301±12,4 MPa) y ACTIVA los más bajos (232±17,2 MPa) a 2mm de espesor (p<0,05). Los valores más bajos de CS se obtuvieron para ACTIVA y los valores más altos para Filtek Z250 para muestras con espesores de 4 y 6mm, respectivamente (p<0,05). Las características estructurales de las resinas compuestas de restauración, como la química; además del tipo y contenido del relleno, y los parámetros operativos (es decir, el espesor del material y las condiciones de curado) afectan en gran medida las reacciones de interacción química y, por lo tanto, los valores de DC, VHN y CS.

Examination of caries-affected dentin and composite-resin interface after different caries removal methods: A scanning electron microscope study.

To evaluate the caries-affected dentin and composite-resin interface with scanning electron microscopy (SEM) after different caries removal methods in human molars. Twelve with extensive approximal caries lesions that did not reach the pulp and five caries-free molars (control group [CG]) were used. Carious teeth were divided into four experimental groups: Atraumatic Restorative Treatment (ART), Rotary Instrument (RI), Photo-Ablation, and Papain-Based Enzymatic Gel (Brix 3000®, Brix, Brazil). Class II slot cavities were prepared with RI in the CG. Then all caries removed teeth and control groups were restored (All-Bond Universal, BISCO, USA; Clearfil MajestyES-2, Kuraray, Japan). Specimens were prepared for SEM examinations. Hybrid layer (HL) thicknesses were measured using ImageJ programme. Gap measurements were performed with micro-CT. Data were analyzed with ANOVA and posthoc Dunnett's t-tests (p < .05). The highest HL thickness was found in Photo-Ablation Group, and a statistically significant difference was observed among the control and experimental groups (p < .05). The lowest HL thickness was measured in the Enzymatic Gel Group. In terms of internal gap formation, CG showed statistically significant differences compared to the other groups (p < .05). The highest internal gap was observed in RI Group, while the lowest gap was observed in CG. According to SEM, a uniform HL and resin tags were seen in the CG. Smear layer, irregular HL, and gap formation were observed in ART Group. In RI Group, nonuniform HL formation and resin tags were observed. In Photo-Ablation Group, a uniform HL without smear layer and internal gap was observed. In the Enzymatic Gel Group, both opened dentinal tubules, and melting-like formations were observed on the dentin surface. Especially melting-like formations were observed in peritubular dentin. It can be concluded that all caries removal methods except rotary instrumentation were conservative methods, which preserve more healthy dental tissues. RESEARCH HIGHLIGHTS: Among the caries removal procedures, the photo-ablation caries removal method stands out with the highest hybrid layer (HL) thickness and the lowest internal gap formation. Despite having the lowest HL thickness, the enzymatic gel method can be advantageous for patients requesting an alternative caries removal instead of a rotary instrument.

Perceptions of dental students towards online education during the COVID-19 pandemic.

PURPOSE: This study evaluated the usage habits, attitudes, and perceptions of undergraduate dental students toward distance (online) learning and identified variables related to those attitudes. MATERIALS AND METHODS: The study included 1,605 undergraduate dental students who participated voluntarily. The data collection tool consisted of a distance learning attitude scale, a questionnaire on personal information, and open-ended questions. The perceptions of dental students to distance education according to the year and type of dental school they attended were evaluated. RESULTS: Most students expressed that distance learning in dental courses was not as effective as traditional face-to-face education (59.1%, n=949). While students studying at state universities had a more negative view of distance education, the satisfaction scores of the first-year students were found to be significantly lower than the other students (p<0.05). CONCLUSION: Dental students were generally unhappy with the interruption of traditional education caused by COVID-19 and having to continue their education online. However, under the circumstances, they saw it as an advantage allowing them to continue their education and avoid a complete suspension.

Knowledge, stress levels, and clinical practice modifications of Turkish dentists due to COVID-19: a survey study.

Dentists are exposed to the highest risk of occupational respiratory and droplet infections by working face-to-face with patients. The aim of this study was to investigate the knowledge of symptoms and modes of transmission of COVID-19, stress levels and clinical practice modifications of Turkish dentists during the COVID-19 pandemic. An online survey (15 questions) was sent to Turkish dentists from May 5 to 12 May, 2020. The survey comprised questions about dentists' demographic characteristics, their knowledge about COVID-19, stress levels and the measures taken in dental clinics against COVID-19. This study included a total of 1,095 Turkish dentists. The data were expressed as frequency with percentage values for overall variables. Dentists were most familiar with high fever among the symptoms of COVID-19 (99.4%) and 99.2% of them reported that COVID-19 was transmitted with eye, mouth and nasal mucosa contact on surfaces contaminated with the droplets of infected persons. While the stress levels of females were higher than males, the stress levels of dentists with more than 20 years of professional experience were found to be lower. Regarding the precautions to be taken as a preventive measure when working again, 86.6% of the dentists took precautions by increasing daily patient care intervals and only 38.4% of the dentists wore an N95 mask. During this pandemic, knowing the conditions about when the treatments can be applied and the precautions to be taken will shed light on dentistry staff. Current recommendations of national authorities about the coronavirus should be followed.

Dentin erosion preventive effects of various plant extracts: An in vitro atomic force microscopy, scanning electron microscopy, and nanoindentation study.

The overall consumption of acidic beverages has become more common, making the prevention and treatment of dental erosion an important consideration. The aim of this in vitro study was to evaluate the effect of various plant extracts in preventing dentin erosion. Seven experimental groups (fluoride-free water, fluoride-containing mouthwash [Colgate Plax], green tea, rosehip, clove, pomegranate, and grape seed) were formed, each consisting of 20 bovine dentin samples. The specimens were exposed daily to demineralization and remineralization cycles three times per day over 5 days through a 5-min plant extract application before each erosive episode. Surface roughness, nanohardness values, and morphological changes on dentin surfaces were examined using atomic force microscopy (AFM), nanoindentation, and scanning electron microscopy (SEM). The data were subjected to Kruskal-Wallis and Friedman tests (p < .05). There were statistically significant differences between the groups in terms of nanohardness values (p < .05), except for the pomegranate and grape seed groups. The highest nanohardness value was observed in the clove group (1.24 ± 0.34 GPa), whereas the lowest nanohardness value was noted in the grape seed group (0.20 ± 0.04 GPa). The nanohardness values of positive and negative control groups after erosion cycles were statistically higher than the initial nanohardness values (p < .05).There was no statistically significant difference between the groups in surface roughness values (p > .05). Macromolecular deposits were observed both in the SEM and AFM images of the pomegranate, Colgate, and rosehip groups. It can be concluded that the clove extract group is more successful in preventing dentin erosion than the other groups. Green tea is also effective in preventing dentin erosion, similar to clove extract. The application of plant extracts may be a new treatment strategy in preventing dentin erosion. Plant extracts may also reduce the severity of existing dentin erosion. Clove and green tea extracts may present novel natural therapy potential by inhibiting dentin erosion.

Knowledge, stress levels, and clinical practice modifications of Turkish dentists due to COVID-19: a survey study

Abstract: Dentists are exposed to the highest risk of occupational respiratory and droplet infections by working face-to-face with patients. The aim of this study was to investigate the knowledge of symptoms and modes of transmission of COVID-19, stress levels and clinical practice modifications of Turkish dentists during the COVID-19 pandemic. An online survey (15 questions) was sent to Turkish dentists from May 5 to 12 May, 2020. The survey comprised questions about dentists' demographic characteristics, their knowledge about COVID-19, stress levels and the measures taken in dental clinics against COVID-19. This study included a total of 1,095 Turkish dentists. The data were expressed as frequency with percentage values for overall variables. Dentists were most familiar with high fever among the symptoms of COVID-19 (99.4%) and 99.2% of them reported that COVID-19 was transmitted with eye, mouth and nasal mucosa contact on surfaces contaminated with the droplets of infected persons. While the stress levels of females were higher than males, the stress levels of dentists with more than 20 years of professional experience were found to be lower. Regarding the precautions to be taken as a preventive measure when working again, 86.6% of the dentists took precautions by increasing daily patient care intervals and only 38.4% of the dentists wore an N95 mask. During this pandemic, knowing the conditions about when the treatments can be applied and the precautions to be taken will shed light on dentistry staff. Current recommendations of national authorities about the coronavirus should be followed.

A Preliminary Research Study on the Cytotoxicity of Expired and Non-expired Composite Resins: In Vitro Study / Estudio preliminar in vitro de la citotoxicidad de resinas compuestas caducadas y no caducadas

Astracts Objective: Studies have focused on use of non-expired composites. Unfortunately some clinicians still use expired composite resins without considering their effects. The objective of this in vitro preliminary research was to investigate cytotoxicity of expired(6-months) and non-expired composite resins. Materials and methods: Expired (E) and non-expired (NE) samples of one bulk-fill (Tetric N-Ceram Bulk-fill (TNB), Ivoclar Vivadent), two nano-hybrid (Tetric N-Ceram (TN), Ivoclar Vivadent; Clearfil Majesty ES-2 (CM), Kuraray) composite resins were tested on L929 fibroblast cells. Medium covering cells was removed then plastic rings (2-mm height) were filled with non-polymerized composite resins, placed in direct contact with cells and polymerized with LED light curing unit (LCU). Three samples were prepared for each group. After polymerization, removed medium was added to the cells. Cells that were left without medium (WOM) and cells that were exposed to LCU were used as positive control groups. Cells without any treatment were used as negative control group (C). Cells were incubated with tested materials for 7-days to evaluate cytotoxicity. Cell viability was calculated by sulforhodamine B test as a percentage (%). One-way ANOVA and post-hoc Tukey tests were used for statistical analyses (p0.05), except between TN NE and TN E (p0.05). All experimental groups compared with C group showed statistically significant cytotoxicity (p<0.05). A statistically significant difference existed between LCU and C groups (p<0.05). Conclusions: In clinical practice, expired composite resins should never be used. Although a correlation was found between expiration dates of nano-hybrid composite resins and cell viability, opposite data were obtained for bulk- fill composite resin. Researches are still required to evaluate biocompatibility of bulk- fill composite resins at various thicknesses with current LCUs.

Resumen Objetivo: Los estudios se han concentrado en el uso de resinas compuestas no vencidos. Desafortunadamente, algunos clínicos aún usan resinas caducadas sin considerar sus efectos. El objetivo de este estudio preliminar in vitro fue investigar la citotoxicidad de resinas compuestas caducadas (6 meses) y no caducadas. Materiales y métodos: muestras caducadas (E) y no caducadas (NE) de una resina bulk-fill (Tetric N-Ceram Bulk-fill (TNB), Ivoclar Vivadent) y dos resinas nanohíbridas (Tetric N-Ceram (TN) Ivoclar Vivadent) (Clearfil Majesty ES-2 (CM), Kuraray), se probaron en células de fibroblastos L929. Se retiraron las células que cubrían el medio, luego se llenaron anillos de plástico (2 mm de altura) con resinas no polimerizadas, se colocaron en contacto directo con las células y se polimerizaron con una unidad de fotocurado LED (LCU). Se prepararon tres muestras para cada grupo. Después de la polimerización, se añadió el medio eliminado a las células. Las células que quedaron sin medio (WOM) y las células que se expusieron a LCU se usaron como grupos de control positivo. Las células sin ningún tratamiento se utilizaron como grupo de control negativo (C). Las células se incubaron con las resinas durante 7 días para evaluar la citotoxicidad. La viabilidad celular se calculó mediante la prueba de sulforodamina B como un porcentaje (%). ANOVA unidireccional y pruebas post-hoc de Tukey se utilizaron para los análisis estadísticos (p 0.05), excepto entre TN NE y TN E (p 0.05). Todos los grupos experimentales en comparación con el grupo C mostraron citotoxicidad estadísticamente significativa (p <0,05). Existió una diferencia estadísticamente significativa entre LCU y grupos C (p <0.05). Conclusiones: En la práctica clínica, las resinas compuestas caducadas nunca deben usarse. Aunque se encontró una correlación entre las fechas de vencimiento de las resinas compuestas nano-híbridas y la viabilidad celular, se obtuvieron datos opuestos para la resina bulk-fill. Se requieren nuevas investigaciones para evaluar la biocompatibilidad de las resinas bulk-fill en distintos espesores con las LCU actuales.

Reactions of Subcutaneous Connective Tissue to Mineral Trioxide Aggregate, Biodentine®, and a Newly Developed BioACTIVE Base/Liner.

AIM: There is an increasing interest in the application of BioACTIVE materials to achieve hard tissue formation and maintain pulp vitality. Mineral trioxide aggregate (MTA) and Biodentine® are BioACTIVE materials used for pulp capping. Recently, dental researchers have produced BioACTIVE glass-incorporated light-curable pulp capping material. The study is aimed at evaluating the subcutaneous connective tissue reactions to MTA, Biodentine®, ACTIVA BioACTIVE Base/Liner. These materials were placed in polyethylene tubes and implanted into the dorsal connective tissue of Sprague Dawley rats. The presence of inflammation, predominant cell type, calcification, and thickness of fibrous connective tissue was recorded by histological examination 7, 30, and 60 days after the implantation procedure. Scores were defined as follows: 0 = none or few inflammatory cells, no reaction; 1 = <25 cells, mild reaction; 2 = 25 to 125 cells, moderate reaction; and 3 = ≥125 cells, severe reaction. Fibrous capsule thickness, necrosis, and formation of calcification were recorded. ANOVA and post hoc Dunnett's tests were used for statistically analyses (p < 0.05). RESULTS: In terms of oedema, inflammation, fibrous capsule, and necrosis, no significant differences were found in any time period for any material. MTA and Biodentine® showed higher calcification than in the ACTIVA BioACTIVE on day 30, and the difference was statistically significant (p < 0.05). After 60 days, while calcification was not seen in the control group, it was observed in the test groups. There was a statistically significant difference between the control and the others. CONCLUSION: All materials were well tolerated by the tissues in the 60-day evaluation period. One notable finding is the presence of dystrophic calcification in the connective tissue adjacent to the newly developed BioACTIVE Base/Liner material. Therefore, this new BioACTIVE Base/Liner material may be safely recommended to clinicians as a pulp capping material.

The use of a liner under different bulk-fill resin composites: 3D GAP formation analysis by x-ray microcomputed tomography.

INTRODUCTION: Gap formation of composite resin restorations is a serious shortcoming in clinical practice. Polymerization shrinkage stress exceeds the tooth-restoration bond strength, and it causes bacterial infiltration within gaps between cavity walls and the restorative material. Thus, an intermediate liner application with a low elastic modulus has been advised to minimize polymerization shrinkage as well as gap formation. OBJECTIVE: The purpose of this in vitro study was to assess gap formation volume in premolars restored with different bulk-fill composites, with and without a resin-modified glass-ionomer cement (RMGIC) liner, using x-ray micro-computed tomography (micro-CT). METHODOLOGY: Sixty extracted human maxillary premolars were divided into six groups according to bucco-palatal dimensions (n=10). Standardized Class II mesio-occluso-distal cavities were prepared. G-Premio Bond (GC Corp., Japan) was applied in the selective-etch mode. Teeth were restored with high-viscosity (Filtek Bulk Fill, 3M ESPE, USA)-FB, sonic-activated (SonicFill 2, Kerr, USA)-SF and low viscosity (Estelite Bulk Fill Flow, Tokuyama, Japan)-EB bulk-fill composites, with and without a liner (Ionoseal, Voco GmbH, Germany)-L. The specimens were subjected to 10,000 thermocycles (5-55°C) and 50,000 simulated chewing cycles (100 N). Gap formation based on the volume of black spaces at the tooth-restoration interface was quantified in mm3 using micro-computed tomography (SkyScan, Belgium), and analyses were performed. Data were analyzed using repeated-measures ANOVA and the Bonferroni correction test (p < 0.05). RESULTS: The gap volume of all tested bulk-fill composites demonstrated that Group SF (1.581±0.773) had significantly higher values than Group EB (0.717±0.679). Regarding the use of a liner, a significant reduction in gap formation volume was observed only in Group SFL (0.927±0.630) compared with Group SF (1.581±0.773). CONCLUSION: It can be concluded that different types of bulk-fill composite resins affected gap formation volume. Low-viscosity bulk-fill composites exhibited better adaptation to cavity walls and less gap formation than did sonic-activated bulk-fill composites. The use of an RMGIC liner produced a significant reduction in gap formation volume for sonic-activated bulk-fill composites.

The use of a liner under different bulk-fill resin composites: 3D GAP formation analysis by x-ray microcomputed tomography

Abstract Gap formation of composite resin restorations is a serious shortcoming in clinical practice. Polymerization shrinkage stress exceeds the tooth-restoration bond strength, and it causes bacterial infiltration within gaps between cavity walls and the restorative material. Thus, an intermediate liner application with a low elastic modulus has been advised to minimize polymerization shrinkage as well as gap formation. Objective: The purpose of this in vitro study was to assess gap formation volume in premolars restored with different bulk-fill composites, with and without a resin-modified glass-ionomer cement (RMGIC) liner, using x-ray micro-computed tomography (micro-CT). Methodology: Sixty extracted human maxillary premolars were divided into six groups according to bucco-palatal dimensions (n=10). Standardized Class II mesio-occluso-distal cavities were prepared. G-Premio Bond (GC Corp., Japan) was applied in the selective-etch mode. Teeth were restored with high-viscosity (Filtek Bulk Fill, 3M ESPE, USA)-FB, sonic-activated (SonicFill 2, Kerr, USA)-SF and low viscosity (Estelite Bulk Fill Flow, Tokuyama, Japan)-EB bulk-fill composites, with and without a liner (Ionoseal, Voco GmbH, Germany)-L. The specimens were subjected to 10,000 thermocycles (5-55°C) and 50,000 simulated chewing cycles (100 N). Gap formation based on the volume of black spaces at the tooth-restoration interface was quantified in mm3 using micro-computed tomography (SkyScan, Belgium), and analyses were performed. Data were analyzed using repeated-measures ANOVA and the Bonferroni correction test (p < 0.05). Results: The gap volume of all tested bulk-fill composites demonstrated that Group SF (1.581±0.773) had significantly higher values than Group EB (0.717±0.679). Regarding the use of a liner, a significant reduction in gap formation volume was observed only in Group SFL (0.927±0.630) compared with Group SF (1.581±0.773). Conclusion: It can be concluded that different types of bulk-fill composite resins affected gap formation volume. Low-viscosity bulk-fill composites exhibited better adaptation to cavity walls and less gap formation than did sonic-activated bulk-fill composites. The use of an RMGIC liner produced a significant reduction in gap formation volume for sonic-activated bulk-fill composites.

Effect of Polymerization Time and Home Bleaching Agent on the Microhardness and Surface Roughness of Bulk-Fill Composites: A Scanning Electron Microscopy Study.

OBJECTIVE: The aim of this study is to evaluate the microhardness and surface roughness of two different bulk-fill composites polymerized with light-curing unit (LCU) with different polymerization times before and after the application of a home bleaching agent. MATERIALS-METHODS: For both microhardness and surface roughness tests, 6 groups were prepared with bulk-fill materials (SonicFill, Filtek Bulk Fill) according to different polymerization times (10, 20, and 30 s). 102 specimens were prepared using Teflon molds (4 mm depth and 5 mm diameter) and polymerized with LCU. 30 specimens (n = 5) were assessed for microhardness. Before home bleaching agent application, the bottom/top (B/T) microhardness ratio was evaluated. After bleaching agent application, the microhardness measurements were performed on top surfaces. Roughness measurements were performed in 72 specimens (n = 12) before and after bleaching application. Additionally, for SEM analyses, two specimens from all tested groups were prepared before and after bleaching agent application. The data B/T microhardness ratio before bleaching was analyzed by two-way ANOVA and Tukey's HSD test. The data from the top surface of specimens' microhardness before and after bleaching were analyzed using Wilcoxon signed-rank test, Kruskal-Wallis, Mann-Whitney U tests. The data from surface roughness tests were statistically analyzed by multivariate analysis of variance and Bonferroni test (p < 0.05). RESULTS: The B/T microhardness ratio results revealed no significant differences between groups (p > 0.05). Comparing the microhardness values of the composites' top surfaces before and after bleaching, a significant decrease was observed exclusively in FB30s (p < 0.05). No significant differences in surface roughness values were observed when the groups were compared based on bulk-fill materials (p > 0.05) while the polymerization time affected the surface roughness of the SF20s and SF30s groups (p < 0.05). After bleaching, surface roughness values were significantly increased in the SF20s and SF30s groups (p < 0.05). CONCLUSION: The clinicians should adhere to the polymerization time recommended by the manufacturer to ensure the durability of the composite material in the oral environment.

Can Fiber Application Affect the Fracture Strength of Endodontically Treated Teeth Restored with a Low Viscosity Bulk-Fill Composite?

OBJECTIVE: The aim of this study is to evaluate the effects of different fiber insertion techniques and thermomechanical aging on the fracture resistance of endodontically treated mandibular premolar teeth restored using bulk-fill composites. MATERIALS AND METHODS: Eighty human mandibular premolar teeth were randomly divided into eight groups: Group IN, Group BF, Group PRF1, Group PRF2, Group IN-TMA, Group BF-TMA, Group PRF1-TMA ,and Group PRF2-TMA. Group IN (intact) and Group IN-TMA (intact but subjected to thermomechanical aging) served as control groups. In the other six groups, endodontic treatment was performed and standardized mesio-occluso-distal (MOD) cavities were prepared. In BF, PRF1, and PRF2, the cavities were restored with bulk-fill composite only, bulk-fill/Ribbond, and bulk-fill/additional Ribbond, respectively. In BF-TMA, PRF1-TMA, and PRF2-TMA, the teeth were subjected to thermomechanical aging after the restorations. All of the teeth were fractured on the universal testing machine. Fracture surfaces were analyzed with a stereomicroscope. RESULTS: Control groups showed significantly higher fracture strengths than tested groups (P<0.05). No statistically significant difference was observed among the tested groups (P>0.05). Most of the favorable fractures were seen in PRF1, PRF2, and PRF2-TMA. Most of the unfavorable fractures were seen in BF-TMA. CONCLUSIONS: Although fiber insertion with different techniques did not increase the fracture strength of teeth restored with bulk-fill composites, it increased the favorable fracture modes. Thermomechanical aging did not change the fracture strength of the groups.

Microhardness and water solubility of expired and non-expired shelf-life composites.

BACKGROUND:: The aim of this study was to determine the Vickers hardness and water solubility of expired and non-expired shelf-life bulk-fill and conventional dental composite material. METHODS:: Four different expired (E) (after 6 months) and non-expired (N) shelf-life composite resin materials (Clearfil Majesty ES-2 Enamel, Clearfil Majesty ES-2 Dentin, Tetric N-Ceram Bulk-Fill, and Tetric N-Ceram) were used. For each tested material, seven specimens were prepared and polymerized with a light curing unit. Vickers hardness measurements were made on the top and bottom surfaces. For the water sorption test, initially all specimens were weighted, the thickness and diameter of each specimen were measured, and the average volume of specimen was calculated. Then, each specimen was immersed in distilled water and kept in an incubator for 7 days and finally weighed again. RESULTS:: There was not any statistically significant difference between the microhardness results of expired and non-expired shelf-life composites on the top and bottom surfaces (p > 0.05). No significant difference was determined between the non-expired shelf-life composite materials on the top surfaces (p > 0.05). Non-expired Clearfil Majesty ES-2 Dentin showed lower microhardness than non-expired Tetric N-Ceram Bulk-Fill and non-expired Tetric N-Ceram on the bottom surface (p < 0.05). Expired Clearfil Majesty ES-2 Dentin showed lower microhardness results than expired Tetric N-Ceram Bulk-Fill on the top and bottom surfaces (p < 0.05). There was not any significant difference between the water sorption results of expired and non-expired shelf-life composites (p > 0.05). Expired Clearfil Majesty ES-2 Dentin showed higher water sorption than expired Tetric N-Ceram E-TN (p < 0.05). CONCLUSION:: Expiration date did not affect the microhardness and water sorption of bulk-fill and conventional composites. The hardness and water sorption of the composite materials varied depending on the type of composites.

Comparison of the micro-tensile bond strengths of four different universal adhesives to caries-affected dentin after ER:YAG laser irradiation.

The micro-tensile bond strengths (micro-TBSs) of four universal adhesive systems, applied in two different bonding techniques, to carries-affected dentin after Er:YAG laser irradiation were investigated. Twenty-four extracted human molars were divided into four groups, according to the adhesive systems used. Each group was subdivided into two subgroups, depending on the bonding method used: the etch-and-rinse procedure or self-etch procedure. The carious lesions were irradiated using an Er:YAG laser. Resin composites were used to restore the adhesive-treated dentin surfaces. After 2,500 thermal cycles, the vertical composite resin-dentin sticks obtained were subjected to micro-TBS tests. One tooth in each group was examined using scanning electron microscopy (SEM). There were statistically significant differences (p<0.001) in micro-TBS values between universal adhesives. The results of this study suggested that universal adhesives applied both with self and total etch technique can be used for adhesive restorations to caries-affected dentin after Er:YAG laser irradiation. If lasers are preferred as a caries removal method, choosing a dentin bonding agent containing MDP may be recommended in clinical practice due to the property of increasing the bonding strength.

Effect of Er:YAG laser enamel conditioning and moisture on the microleakage of a hydrophilic sealant.

For a given sealant, successful pit and fissure sealing is principally governed by the enamel conditioning technique and the presence of moisture contamination. A new generation of hydrophilic resin sealants is reported to tolerate moisture. This study investigates the impact of Er:YAG laser pre-conditioning and moisture contamination on the microleakage of a recent hydrophilic sealant. Occlusal surfaces of extracted human molars were either acid etched (n = 30), or successively lased and acid etched (n = 30). Ten teeth from each group were either air-dried, water-contaminated, or saliva-contaminated prior to sealing with UltraSeal XT® hydro™. Samples were inspected for penetration of fuchsin dye following 3000 thermocycles between 5 and 50 °C, and the enamel-sealant interfaces were observed by scanning electron microscopy (SEM). Significant differences in microleakage were evaluated using the Mann-Whitney U test with Bonferroni adjustment (p = 0.05). Laser pre-conditioning significantly reduced dye penetration irrespective of whether the enamel surface was moist or dry. Microleakage of water-contaminated acid etched teeth was significantly greater than that of their air-dried or saliva-contaminated counterparts. SEM analysis demonstrated good adaptation in all groups with the exception of water-contaminated acid etched teeth which exhibited relatively wide gaps. In conclusion, this hydrophilic sealant tolerates the presence of saliva, although water was found to impair its sealing ability. Laser pre-conditioning significantly decreases microleakage in all cases.

Characterisation and microleakage of a new hydrophilic fissure sealant - UltraSeal XT® hydro™.

OBJECTIVES: The aim of this study was to characterise the new hydrophilic fissure sealant, UltraSeal XT® hydro™ (Ultradent Products, USA), and to investigate its in vitro resistance to microleakage after placement on conventionally acid etched and sequentially lased and acid etched molars. MATERIAL AND METHODS: The sealant was characterised by Fourier transform infra-red spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and Vickers indentation test. Occlusal surfaces of extracted human molars were either conventionally acid etched (n=10), or sequentially acid etched and laser irradiated (n=10). UltraSeal XT® hydro™ was applied to both groups of teeth which were then subjected to 2,500 thermocycles between 5 and 55°C prior to microleakage assessment by fuchsin dye penetration. RESULTS: UltraSeal XT® hydro™ is an acrylate-based sealant that achieved a degree of conversion of 50.6±2.2% and a Vickers microhardness of 24.2±1.5 under standard light curing (1,000 mWcm-2 for 20 s). Fluoride ion release is negligible within a 14-day period. SEM and EDX analyses indicated that the sealant comprises irregular submicron and nano-sized silicon-, barium-, and aluminium-bearing filler phases embedded in a ductile matrix. Laser preconditioning was found to significantly reduce microleakage (Mann-Whitney U test, p<0.001). The lased teeth presented enhanced surface roughness on a 50 to 100 µm scale that caused the segregation and concentration of the filler particles at the enamel-sealant interface. CONCLUSION: Laser preconditioning significantly decreased microleakage and increased enamel surface roughness, which caused zoning of the filler particles at the enamel-sealant interface.

Characterisation and microleakage of a new hydrophilic fissure sealant - UltraSeal XT® hydro

ABSTRACT Objectives The aim of this study was to characterise the new hydrophilic fissure sealant, UltraSeal XT® hydro™ (Ultradent Products, USA), and to investigate its in vitro resistance to microleakage after placement on conventionally acid etched and sequentially lased and acid etched molars. Material and Methods The sealant was characterised by Fourier transform infra-red spectroscopy (FTIR), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX), and Vickers indentation test. Occlusal surfaces of extracted human molars were either conventionally acid etched (n=10), or sequentially acid etched and laser irradiated (n=10). UltraSeal XT® hydro™ was applied to both groups of teeth which were then subjected to 2,500 thermocycles between 5 and 55°C prior to microleakage assessment by fuchsin dye penetration. Results UltraSeal XT® hydro™ is an acrylate-based sealant that achieved a degree of conversion of 50.6±2.2% and a Vickers microhardness of 24.2±1.5 under standard light curing (1,000 mWcm-2 for 20 s). Fluoride ion release is negligible within a 14-day period. SEM and EDX analyses indicated that the sealant comprises irregular submicron and nano-sized silicon-, barium-, and aluminium-bearing filler phases embedded in a ductile matrix. Laser preconditioning was found to significantly reduce microleakage (Mann-Whitney U test, p<0.001). The lased teeth presented enhanced surface roughness on a 50 to 100 μm scale that caused the segregation and concentration of the filler particles at the enamel-sealant interface. Conclusion Laser preconditioning significantly decreased microleakage and increased enamel surface roughness, which caused zoning of the filler particles at the enamel-sealant interface.

Effect of storage temperature on bond strength of a self-etch adhesive system to pulp chamber dentin.

OBJECTIVES: The aim of this study was to evaluate the effect of storage temperature on bond strength of a self etching primer system to pulp chamber dentin. METHODS: SE Bond (Kuraray, JAPAN) adhesive system and Clearfil Photo Posterior (Kuraray, JAPAN) composite resin were used. Eight extracted caries-free human molar teeth were used. Access cavities were prepared through the pulp chamber, randomly distributed into 4 groups and prepared as follows: Group 1 (Control): SE Primer and SE Bond (SEB) were applied to the pulp chamber dentin according to the manufacturer's instructions, immediately after the delivery from the manufacturer and then the pulp chamber was restored with a resin restorative material. The primer agent of the following groups was stored in a refrigerator and kept at 4 degrees C. Group 2: restored with SEB, kept at 4 degrees C refrigerator for 1 year, Group 3: restored with SEB kept at 23 degrees C room temperature for 1 year and Group 4: restored with SEB kept at 40 degrees C incubator for 1 year. After 24 hrs the teeth were trimmed for microtensile bond testing and loaded to failure at 1mm/min. Data were analyzed using one-way ANOVA and Duncan test (P<.05). RESULTS: The results indicated that Group 4 showed lowest bond strength when compared to the others (P<.05). No statistically significant difference was found among the other groups (P>.05). CONCLUSIONS: As a result of this study, it was concluded that increasing storing temperature or storing period decreases microtensile bond strength of a SEB system to pulp chamber dentin.

Effect of artificial saliva contamination on bond strength to pulp chamber dentin.

OBJECTIVES: The purpose of this in vitro study was to evaluate the effect of artificial saliva contamination on microtensile bond strength to pulp chamber dentin. METHODS: Clearfil SE Bond (SEB) (Kuraray, JAPAN) adhesive system and Clearfil Photo Posterior (CPP) (Kuraray, JAPAN) composite resin were used. Twenty extracted caries-free human molar teeth were randomly distributed into four groups. Apart from a control group without contamination (Group 1), primed dentin surfaces were contaminated with artificial saliva (10 s), rinsed, dried, re-primed and bonded (Group 2), coated with adhesive, contaminated with artificial saliva, rinsed, dried, bonding procedures were repeated (Group 3), coated with adhesive, light cured, contaminated with saliva, rinsed, dried, treated with SE primer (SEP) and SEB (Group 4). After 24 hrs, the teeth were prepared for microtensile bond testing and tensile bond strength was measured (1mm/min). The data was calculated as MPa and analyzed using one-way ANOVA and Duncan test (P<.05). RESULTS: The results indicated that Group 2 showed lowest bond strength when compared to the others (P<.05). No statistically significant difference was found between Groups 3 and 4 (P>.05). CONCLUSIONS: It was concluded that contamination during priming procedure has a negative effect on bond strength (P<.05). Although contamination of the uncured adhesive was not critical in this study (P>.05) any kind of contamination of the bonding area should, in principle, be avoided.